If the Whirlpool washer displays the de error code on display, so there are problems with a door.
Manual Review
Unplug the Whirlpool washing machine from the mains.Wait for 15-20 minutes while the control unit reboots.Reset the error by pressing the START button (On/Off).Check hatch locking.
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
Why does my washing machine keep saying error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
How do I reset my Whirlpool?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do I fix the error on my washing machine?
An error code on the display of the washer can usually be resolved by performing a few simple troubleshooting steps.
To fix this:
Unplug the washer for 10 seconds.Plug the washer back in, and press power button. Once the washer is drained, restart the washing cycle process.
What does F5 mean on a Whirlpool washer?
Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
How do I fix E01 F09 Whirlpool?
Faulty Drain Pump
Check for any obstructions throughout the drainage system.Use the Quick Diagnostics Test to check the pump and its connections.Unplug the washer’s power cord.Uninstall the top panel.Make sure that the DP2 connector is fully inserted into the Central Control Unit (CCU)
What does E01 and F06 mean on a Whirlpool washer?
A Whirlpool washer error code E01/F06 indicates that the washer’s motor control unit (MCU) is having trouble communicating with the washer’s central control unit (CCU). In most cases, the issue is caused by a damaged MCU circuit, usually caused by an overload.
How do I fix E01 error on my Whirlpool washer?
How to Fix Whirlpool Washer F3/E1 Error Codes
What Does the F03/E01 Error Code Mean?Step 1 – Reset Your Washer.Step 2 – Check the Switch Hose.Step 3 – Check the Water Level Sensor.Step 4 – Check the Air Trap Pipe.Step 5 – Check the Wiring.Step 6 – Replace the Control Board.
What does E1 mean on washing machine?
When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water. To resolve, checking the following: • Check whether the water supply is turned on and that there is adequate water pressure.
How do I fix error F7 E1?
Cycle Power
If the power cord is accessible, try resetting the machine by unplugging and replugging the power cord to the wall outlet. Restart the cycle. If the problem persists, call for service.
How do I clear the error code on my Kenmore washer?
How to Reset the FH Error Code on a Kenmore Elite Washing Machine
Look for the “Pause/Cancel” button on the washer control panel. Press the “Pause/Cancel” button twice to cancel the wash cycle. Check for kinks in the water supply hose while the washer does not have power.
